Tecno KC2 Dead After Flash – Recover Boot Tested File MT6761 Spark 4

Introduction

A smartphone can get bricked when flashing goes wrong. Most users of the Tecno KC2 (Spark 4) have surely seen their phones die after flashing them, either due to wrong firmware, a flash cut short, or incorrect files. If this happens and your Tecno KC2 (MT6761) fails to switch on post flashing, worry not as it can possibly be rescued with a good boot file and appropriate flash tools.

This guide will teach you how to revive a dead Tecno KC2 (Spark 4) using a working MT6761 boot file and SP Flash Tool.

What Makes a Tecno KC2 Die After Flashing?

There are different reasons why a Tecno KC2 dies after flashing:

Triadrics firmware: Wrong firmware version or mismatch due to scatter files can brick the device.

Interrupted Flashing Process: Flashing is stopped midway usually by USB disconnection, power failure, etc.; therefore, it will not boot.

Bad Flashing Method: Wrong flash method used by (for example, only Download Only or Format All + Download) might also brick it.

Recovery Processes
Before you start, you must have:

✔ Windows PC (Windows 7/8/10/11 would be better)
✔ SP Flash Tool (newest version download)
✔ Tecno KC2 (Spark 4) MT6761 Firmware (boot file checked)
✔ MediaTek USB VCOM drivers for Tecno KC2
✔ Good original USB cable
✔ Full battery (at least 30%)

Step by Step Recovery Guide

1. Download and Set Up Needed Tools
– Get SP Flash Tool- Only from their official site.

– Put in MediaTek USB Driver-so your computer recognizes your phone in BROM mode.

– Boot File for Tecno KC2 (MT6761) Testing-Source from trusted sites (e.g. FirmwareFile.com or AndroidMTK).

2. Extract and Load Firmware into SP Flash Tool
Extract your firmware files.

Open SP Flash Tool and hit scatter-loading.

Locate your firmware folder and select the MT6761_Android_scatter.txt file.

3. Flash Only the Boot Image
Since the phone is dead, we will flash just the boot.img to fix it:

Uncheck all files except boot.img in SP Flash Tool.

“Download Only” is selected (do NOT select Format All).

4. Put Tecno KC2 into BROM Mode
Since the phone is dead, you actually have to force it into BROM Mode:

Turn off the phone if it’s on.

Hold down the Volume Down and Power buttons (or Volume Up + Volume Down + Power on some models).

Go on to connect the phone to the PC via USB while the buttons are still pressed.

Let go of the buttons when the PC sees the phone (a new COM port shows in Device Manager).

5. Start Flashing the Boot Image
In SP Flash Tool, Click the “Download” button.

Wait until the flash is completed (green checkmark appears).

Remove the phone and press the Power button to start it.

You May Also Like This Post :: Best Flashing Tools 2025

What If Phone Still Does Not Start?

If it happens that the above method won’t work, here are some factors one might want to consider:

✔ Flash Preloader & Boot Files- Sometimes, preloader can be bad.
✔ Firmware Upgrade Mode- This is better than Download Only in SP Flash Tool.
✔ Full Flashdown if boot.img fails alone, just make sure to save from NVRAM first.
✔ Check Battery & Hardware-Ensure the Battery is not Empty or Broken.

Prevent Future Bricking Issues

To keep your phone alive after flashing.

🔹 Always use the correct firmware for your model.
🔹 Do not interrupt the flashing process.
🔹 Save NVRAM & IMEI before flashing.
🔹 Good USB cable and stable power.

Download Link: HERE
Your File Password: NewGSMSolution.com
File Size : 1.70 GB
File type: compressed/Zip & RAR (Use 7zip or WINRAR to unzip file)
Support OS: All Windows (32-64Bit)
Upload By: Ghulam Sarwar
Virus Status: 100% Safe Scanned By Avast Antivirus