VGO Tel V Tab 2 Readed Firmware – Unbrick Hang On Logo Boot Loop Stuck Menu Fix File

VGO Tel V Tab 2 is an uncomplicated and convenient introduction tool to the wide family of Android tablets. However, it is not immune to the same kind of ‘unresponsive’ file corruptions that the others suffer from. A boot loop is merely one of those typical problematic incidents that often annoy the user the most. When stuck in a boot loop, a device will continually be going through the start-up and shut down cycle but at the same time, would never be able to bypass the logo screen. Besides, trouble also manifest itself stuck in recovery menu, or hanging on  black screen. Usually, a software reinstall utilizing “Readed Firmware” or “Fix File” is the only method that can solve this problem. This guide will actually explain these two words along with a detailed, stepwise manual of how to unbrick your VGO Tel V Tab 2.

What to Understand about the Issue: What are Reasons for a Boot Loop?

The occurrence of a boot loop or stuck logo problem is quite a signal of software corruption in the device which it cannot properly load. Some of the most frequent causes of this are:

. Unsuccessful Software Update: A stoppage during the official Over-The-Air (OTA) update or a manual firmware installation can make the system partition corrupted.

. An Unfavorable App or Alteration: An uncompatible app, a malfunctioned root mod, or an incorrect change of build.prop can make the operating system unstable.

. Virus or Malware: Malicious software that attacks the system files of Android tablets is just as dangerous as for smartphones, however, it is less likely to happen.

. Hardware Failure: There are times when the reason for a hang-on-logo issue is a hardware problem of the device rather than software, such as internal storage (eMMC) that is broken.

Under  conditions,  factory reset or “wipe data/factory reset” generally done through  recovery mode  not strong enough system core files already corrupted. Hence,  part  using “full firmware restore” takes over.

What “Readed Firmware” or “Fix File”?

“Readed Firmware” is an extracted directly or “read” firmware from an originally and normally operating unit of the exact same model as the one that needs repair. In other words, this is the way to ascertain that the firmware is the factory one and that it encompasses all the required partitions such as boot, system, recovery, and userdata for a complete restoration.

A “Fix File”  a set files  developed to solve  issues that  most likely causes software failure. It generally comprises the necessary files like the preloader, boot image, and system image for the boot process. usually more secure to install an experimental “Fix File” rather  a common firmware download because  tailored  resolve  very “hang on logo” or “boot loop” predicament VGO Tel V Tab 2.

Fixing Prerequisites

Before proceeding with the fix, make sure that you have all the required tools and information at your disposal. The wrong files can damage your tablet beyond a point of no return.

1.The Correct Firmware: This is the most critical step. You have to look for the exact “Readed Firmware” or “Fix File” that is compatible with the model number of your VGO Tel V Tab 2. Most of the time, the model number is on a label on the back of the device or on the original packaging (e.g., VGOTEL_V_Tab_2). Installing firmware from a different model will lead to a “brick” of your device.

2. Windows PC/Laptop: Generally, the flashing tool that you use is Windows-based.

3. USB Cable: Select a good quality USB cable for data sync use. cables only used  charging not functional.

4. Flasher Tool: The standard software for flashing mediaTek (MTK) chipset tablet SP Flash Tool is used. One should have the right version of a tool that corresponds to the firmware of the tablet.

5. MTK VCOM USB Drivers: These are the drivers which need to be installed in your PC so that it can recognize the tablet in “BROM Mode” (a low-level communication mode) especially when the device is off.

6. Battery Charge: Make sure that the battery of the tablet is charged from 30% to 50% in order to avoid shutdown during the flashing process.

Step-by-Step Unbricking Guide using SP Flash Tool

Warning: This process will delete everything from your tablet. It is unrecoverable. Operate at your own risk.

1.Prepare Your PC: Place the MTK VCOM USB Drivers on your Windows computer. Most times, it also involves turning off the driver signature enforcement.

2. Extract Files: Get the “VGO Tel V Tab 2 Readed Firmware” file for download. It will most probably be in a compressed (.rar or .zip) format. Take the files out of the folder and save them in one that is easily reachable on your desktop.

3. Open SP Flash Tool: CALLING the location STORE for SP Flash Tool in the directory where you stored it then running the executable file (e.g., flash_tool.exe).

The real athantic website for GSM files & tools Of all kind

4. Load the Scatter File: Perform a browser operation on SP Flash Tool to select the command “Scatter-loading” for the directory where you unpacked the firmware. Ideally,  computer reads  file,  presented filename MTXXXX_Android_scatter.txt (e.g., MT6737_Android_scatter.txt). The device suggest a variety all software partitions now.

5. Select the Download Agent: Find the “Download-Agent” prompt, press the button, pick the file labeled DA_PL.bin if it’s an element of your firmware directory. If not, the tool might simply obtain one without your help.

6. Pick Switch Turning-on Way: At the very top of the drop-down menu where you decide the next step, the “Download Only” option is substituted by “Firmware Upgrade”. This is just a repair-oriented mode of the device.

7. Start the Flashing Process: Without leaving any step unfinished, press the “Download” button on the SP Flash Tool interface.

8. Attach the Tablet: Now completely shut down your VGO Tel V Tab 2 and definitely do not link it to the PC at this point. Connect your powered-off tablet to the PC with the USB cable while the Flash Tool is there awaiting. The tool should automatically detect the device and commence the flashing process. You shown progress bar  each partition written.

9. Ending: When the action is done, a big green circle with the word “OK” on it will be visible to you.

1o. Disconnect and Reboot: Take out the USB cable. Now, you can press and hold the Power button of your tablet to turn it on.

Download Link: HERE
Your File Password: NewGSMSolution.com
File Version & Size : |
File type: compressed/Zip & RAR (Use 7zip or WINRAR to unzip file)
Support OS: All Windows (32-64Bit)
Upload By: Ghulam Sarwar
Virus Status: 100% Safe Scanned By Avast Antivirus